G82218 B型电火花真空检测器
供应商:北京冠测精电仪器设备有限公司[查看公司详情]
所在地:北京市昌平科技园区凉水河路一号院创意大厦2号楼1010室
价格:100元/个
经营模式:
联系人:章飞
产品简介
B型电火花真空检测器
一、电火花真空检测仪概述
本产品利用高频电火花检测各种器件真空程度,具有安全可靠,使用方便的特点,是电子管、阴极射线管、气体激光管、各种灯泡等玻璃抽气产品检测真空程度的必须仪器。
二、电火花真空检测仪主要性能
1.火花束长度:≥20mm
2.工作方式:间歇使用
3.温升:连续使用半小时,不超过60℃
4.适用电源:~220V,±10%
5.电源频率:50±3HZ
6.耗电功率:不大于30W
7.检测范围:200~10-3托
8.重量:0.6公斤
三、电火花真空检测仪工作原理
接通电源后由L1与CD产生振铃,在CD的触点之间发生电火花现象,激励C及L2组成的回路串联谐振,经L3感应产生高频电压,然后由放电簧F放出高频电火花,即可使用。
四、电火花真空检测仪调整及使用
先把放电簧插头插入前面插座,然后将电源插头插入220V/50HZ交流电源,接通开关,此时在放电簧端应看到紫色火花。将放电簧移近任何金属物体时,应产生不少于三条火花线,长度不短于20MM。如无火花产生或火花线甚少,或长度甚短,则可调节检测器后面的旋钮,便产生火花,并调节火花至最多最长为止。
火花正常后,便可对电子管或其他玻璃真空容器检测其真空程度。
将放电簧对准被测器件,如其真空度相当高时,则紫色火花局限在玻璃壁外。若真空度不高或非真空时,放电簧端的高频电火花(高压)引起容器内气体电离,并产生辉光。
五、电火花真空检测仪注意事项
1.本产品供间歇使用(即时开关)如需连续使用(即长时间开着),应需注意,勿使温升超过120℃,以免烧毁线圈。
2.使用时,人体不能靠近或接触高压线圈圆锥形部分,否则有强烈火花电弧跃出会将线圈烧坏。
3.在测玻璃器件时,必须来回移动不要停留,若时间超过五秒钟以上,电火花易将玻璃击穿。
4.在检测器使用一段时间后,接触部分可能会烧浊,可用砂布砂光后继续使用。
5.平时不用时应将调节旋钮旋出(即逆时针旋转),使用时把旋钮缓缓旋入(顺时针方向旋转),但应防止接触头短路,将震动线圈烧坏。万一发生接触头短路,(或其他故障)时将内部拆卸出来检修。
B
type edm vacuum detector
An overview, edm vacuum tester
This product use
of high-frequency electric spark testing device, vacuum degree, have a safe and
reliable, easy to use, the characteristics of tube, a cathode ray tube, gas
laser tube, all kinds of light bulbs and other glass extraction product testing
the vacuum degree of must equipment.
Second, the electric spark vacuum gauge
performance
1. The length of fire bouquet: 20 mm or higher
2. Work style:
intermittent use
3. The temperature rise: continuous use half an hour, less
than 60 ℃
4. Apply power: ~ 220 v, + / - 10%
5. Power frequency: 50 + 3
hz
6. Electricity power: no more than 30 w
7. Test: the range of
200-10-3
8. Weight: 0.6 kg
3, edm vacuum working principle of the detector
After
turning on the power supply is produced by L1 and CD ringing, edm ur between
the contact of the CD, the incentive of C and L2 loop series resonance, the L3
induction to produce high-frequency voltage, then the discharge spring F emit
high-frequency electric spark, can be used.
Four, electric spark vacuum
tester adjustment and use
The discharge first spring plug into the socket,
and then insert the plug into 220 v / 50 hz ac power, turn on the switch, at
this point in the spark discharge spring end should see purple. Move discharge
spring nearly any metal objects, should be not less than three spark producing
line, the length of not less than 20 mm. If there is no spark or spark
producing line, or length is very short, can adjust the detector at the back of
the knob, then produce sparks, and adjust the spark to the maximum of the
longest.
Spark is normal after, can on the tube or other glass vacuum
container testing the vacuum degree.
Aim the discharge in spring, the device
being tested as the vacuum degree is quite high, the purple spark limited
outside the glass wall. If the vacuum degree is not high, or the vacuum, spring
the high frequency electric spark discharge (high pressure) container gas
ionization, and generate glow.
Five, the electric spark vacuum tester
1.
This product is for the use of intermittent (instant switch) for continuous use
(open) for a long time, should pay attention to, don\'t make the temperature
over 120 ℃, so as to avoid burning coil.
2. When used, the body can\'t close
to or contact with high voltage coil conical part, otherwise a strong spark arc
spring coil will be burn out.
3. When the glass measuring device, must move
back and forth and not to stay, if the time is more than five seconds, electric
spark breakdown easy to glass.
4. Use after a period of time in the
detector, the contact part may burn turbidity, available emery cloth continue
to use after sanding.
5. At ordinary times need not when adjusting knob
should be spin out (counterclockwise), when using the knob slowly screwing in
(clockwise), but should prevent contact short circuit, vibration coil burn out.
One thousand contact head short circuit, (or other malfunction) when the
internal remove out maintenance.
产品为冠 源于精测
精品摇篮 王者之选