ABS电镀表面丝印移印油墨
供应商:上海凯贤印刷科技有限公司[查看公司详情]
所在地:上海市嘉定区沪宜公路6106号
价格:180.00元/千克
经营模式:生产加工
联系人:赵绿林
产品简介
品牌:欧莱斯,
型号:MPE,
印刷方式:丝印移印,
连接料:树脂油型,
承印物:电镀,
干燥形式:自然干燥,
颜色:不限,
产地:德国,
叠印性:强,
外观:膏状,
含水量:0.0021%,
颗粒细度:99.99μm,
粘度:100S,
附着强度:100,
稳定性:10,
流动性:0.013mm,
干燥时间:3-5min,
渗透性:10μm,
储存温度:22-23℃,
包装规格:1008ml,
保质期:48,
适用范围:真空电镀、水电镀、强化电镀、金属电镀、塑胶电镀、五金电镀,
特性:免烘烤、单组份、双组份、自干,
外光:高光泽、高色彩、高硬度,
特质:耐酒精、耐酸碱、耐汽油、耐摩擦、抗腐蚀,
印刷方式:丝印、移印、喷涂,
75电镀强化系列油墨
油墨特性: 主要用于电镀表面、强化表面、真空电镀表面.PU表面.UV表面等材料上,具有高色泽、高色彩、高遮盖力、高稳定性、耐酒精及耐磨擦之特点。
印刷:丝印移印均可。 表干及实干时间:表干时间自然挥发5-10分钟;实干时间在24小时以内。
稀释及清洗:SV3慢干开油水、UVK1(移印开油水)同时可使用718洗网水清洗。 测试方法(干燥后):
1、3m胶纸粘在画有百格的油墨表面,45度角迅速拉起不脱油; 2、纯度99%的工业酒精,一千克砝码用棉布包住在油墨表面,以水平力来回拉200次无脱色; 3、
耐磨:橡皮擦500g力水平来回擦500次。 使用方法: 1、使用前应充分搅拌,用后随时封闭; 2、搅拌时加开油水10-15%,稀释到印刷粘度;
3、网板塞网时可用洗网水清洗; 4、不得与其它类型油墨混合使用。 注意事项:
1、塑胶材料的外观相似,但可能会是不同的材料,客户需试印确定其符合要求后,再批量印刷; 2、在移印过程中,如出现拉丝或散开,可适当加入一些慢干膏即可;
3、环境温度过高,将会影响油墨原有质量; 4、根据气候变化,请远离火源,阴暗环境下存放。75
plating strengthening series ink characteristics: mainly used in plating
surface, enhanced surface, vacuum platingsurface.PU surface.UV surface and
other materials, with a high color, high color, high covering power, alcohol
resistant and wear resistance, high stability. Printing: silk screen printing
can be. Table dry and work time: surface dry time natural volatile 5-10
minutes; work time within 24 hours. Dilution and cleaning: SV3 slow dry open
water,UVK1 (printing open water) also can use 718 washing network water
cleaning. Test method (completely dry): 1,3M adhesive tape sticky ink surface
adhesion in painting,45 degree angle quickly pulled off the oil; 2, purity 99%
of industrial alcohol, using cotton bag in the surface of the inkone kilogram
weight to horizontal force and pull 200 timeswithout decolorization; 3, wear:
rubber eraser 500g forcelevel wipe 500 times back and forth. Method of use:
1,before the use should be fully mixing, be closed after use;2, stirring an
additional oil 10-15%, dilution to printingviscosity; 3, mesh plug mesh can be
used when washing network water cleaning; 4, shall not be mixed with othertypes
of ink. Note: 1, the plastic material of similar appearance, but may be of
different materials, customers need to try to determine its requirements, and
then batchprinting; 2, in the printing process, such as drawing or spread out,
may be appropriate to add some slow dry pastecan; 3, the ambient temperature is
too high, it will affect thethe quality of the original ink; 4, according to
the climate change, please stay away from fire, stored in dark
相关产品推荐